收藏本站
Si1141/42/43
4. Programming Guide
4.1. Command and Response Structure
All Si1141/42/43 I 2 C registers (except writes to the COMMAND register) are read or written without waking up the
internal sequencer. A complete list of the I 2 C registers can be found in "4.5. I2C Registers" on page 28. In addition
to the I 2 C Registers, RAM parameters are memory locations maintained by the internal sequencer. These RAM
Parameters are accessible through a Command Protocol (see "4.6. Parameter RAM" on page 52). A complete list
of the RAM Parameters can be found in "4.6. Parameter RAM" on page 52.
The Si1141/42/43 can operate either in Forced Measurement or Autonomous Mode. When in Forced
Measurement mode, the Si1141/42/43 does not make any measurements unless the host specifically requests the
Si1141/42/43 to do so via specific commands (refer to the Section 3.2). The CHLIST parameter needs to be written
so that the Si1141/42/43 would know which measurements to make. The parameter MEAS_RATE, when zero,
places the internal sequencer in Forced Measurement mode. When in Forced Measurement mode, the internal
sequencer wakes up only when the host writes to the COMMAND register. The power consumption is lowest in
Forced Measurement mode (MEAS_RATE = 0).
The Si1141/42/43 operates in Autonomous Operation mode when MEAS_RATE is non-zero. The MEAS_RATE
represents the time interval at which the Si1141/42/43 wakes up periodically. Once the internal sequencer has
awoken, the sequencer manages an internal PS Counter and ALS Counter based on the PS_RATE and
ALS_RATE registers.
When the internal PS counter has expired, up to three proximity measurements are made (PS1, PS2 and PS3)
depending on which measurements are enabled via the upper bits of the CHLIST Parameter. All three PS
measurements are performed, in sequence, beginning with the PS1 measurement channel. In the same way, when
the ALS counter has expired, up to three measurements are made (ALS_VIS, ALS_IR and AUX) depending on
which measurements are enabled via the upper bits of the CHLIST Parameter. All three measurements are made
in the following sequence: ALS_VIS, ALS_IR and AUX.
PS_RATE and ALS_RATE are normally non-zero. A value of zero in PS_RATE or ALS_RATE causes the internal
sequencer to never perform that measurement group. Typically, PS_RATE or ALS_RATE represents a value of
one. A value of one essentially states that the specific measurement group is made every time the device wakes
up.
It is possible for both the PS Counter and ALS Counter to both expire at the same time. When that occurs, the PS
measurements are performed before the ALS measurements. When all measurements have been made, the
internal sequencer goes back to sleep until next time, as dictated by the MEAS_RATE parameter.
The operation of the Si1141/42/43 can be described as two measurement groups bound by some common factors.
The PS Measurement group consists of the three PS measurements while the ALS Measurement group consists
of the Visible Light Ambient Measurement (ALS_VIS), the Infrared Light Ambient Measurement (ALS_IR) and the
Auxiliary measurement (AUX). Each measurement group has three measurements each. The Channel List
(CHLIST) parameter enables the specific measurements for that measurement grouping.
Each measurement (PS1, PS2, PS3, ALS_VIS, ALS_IR, AUX) are controlled through a combination of I2C
Register or Parameter RAM. Tables 7 to 9 below summarize the properties and resources used for each
measurement.
Rev. 1.3
19
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SI1300BDL-T1-GE3 MOSFET N-CH D-S 20V SC-70-3
SI1302DL-T1-GE3 MOSFET N-CH D-S 30V SC-70-3
SI1303DL-T1-GE3 MOSFET P-CH 20V 670MA SOT323-3
SI1305DL-T1-GE3 MOSFET P-CH G-S 8V SC-70-3
SI1307EDL-T1-GE3 MOSFET P-CH G-S 12V SC-70-3
SI1401EDH-T1-GE3 MOSFET P-CH F-D 12V SC-70-6
SI1426DH-T1-GE3 MOSFET N-CH D-S 30V SC-70-6
SI1469DH-T1-GE3 MOSFET P-CH 20V SC-70-6
相关代理商/技术参数
Si1143-A11-GMR 功能描述:近程传感器 I2C Proximity Amb Light Sensor 3 LED RoHS:否 制造商:Vishay Semiconductors 感应方式:Optical 感应距离:1 mm to 200 mm 电源电压:2.5 V to 3.6 V 安装风格:SMD/SMT 输出配置:Digital 最大工作温度:+ 85 C 最小工作温度:- 25 C 系列:VCNL3020
SI1143-M01-EVB 功能描述:Si1141-M01, Si1142-M01, Si1143-M01 - Light and Proximity Sensor Evaluation Board 制造商:silicon labs 系列:- 零件状态:有效 传感器类型:光线和近程 感应范围:- 接口:I2C 灵敏度:- 电压 - 电源:1.71 V ~ 3.6 V 嵌入式:- 所含物品:2 板，线缆 使用的 IC/零件:Si1141-M01，Si1142-M01，Si1143-M01 标准包装:1
SI1143-M01-GMR 功能描述:Optical Sensor IR 850nm I2C 10-SMD Module (No Lead) 制造商:silicon labs 系列:- 包装:剪切带（CT） 零件状态:有效 类型:IR 波长:850nm 接近探测:是 输出类型:I2C 电压 - 电源:1.71 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-SMD 模块（无引线） 供应商器件封装:10-QFN（4.9x2.9） 标准包装:1
SI1145-A10-GMR 功能描述:Optical Sensor Ambient I2C 10-WFQFN 制造商:silicon labs 系列:- 包装:剪切带（CT） 零件状态:有效 类型:环境 波长:- 接近探测:是 输出类型:I2C 电压 - 电源:1.71 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFQFN 供应商器件封装:10-QFN（2x2） 标准包装:1
SI1145-M01-GMR 功能描述:Optical Sensor IR 850nm I2C 10-SMD Module (No Lead) 制造商:silicon labs 系列:- 包装:剪切带（CT） 零件状态:有效 类型:IR 波长:850nm 接近探测:是 输出类型:I2C 电压 - 电源:1.71 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-SMD 模块（无引线） 供应商器件封装:10-QFN（4.9x2.9） 标准包装:1
SI1146-A10-GMR 制造商:Silicon Laboratories Inc 功能描述:I2C UV INDEX AND PROXIMITY/AMBIENT LIGHT SENSOR WITH 2 LED D - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:SENSOR DGTL UV INDEX QFN
SI1146-M01-GMR 功能描述:Optical Sensor IR 850nm I2C 10-SMD Module (No Lead) 制造商:silicon labs 系列:- 包装:剪切带（CT） 零件状态:有效 类型:IR 波长:850nm 接近探测:是 输出类型:I2C 电压 - 电源:1.71 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-SMD 模块（无引线） 供应商器件封装:10-QFN（4.9x2.9） 标准包装:1
SI1147-A10-GMR 功能描述:Optical Sensor Ambient I2C 10-WFQFN 制造商:silicon labs 系列:- 包装:剪切带（CT） 零件状态:有效 类型:环境 波长:- 接近探测:是 输出类型:I2C 电压 - 电源:1.71 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFQFN 供应商器件封装:10-QFN（2x2） 标准包装:1